GKDMINI-20210201-v030

User tutorial

[Tutorial] psx change bios
Open the ps1 sub-disk, change to rec, core setting-emulation core rec, set Bios file, select scph1001.bin, the general BISO, B returns, and Quit exits. Change to the same method as other specific BIos.
Enter the PS1 game, select any game, press the select and start keys at the same time to call up the settings menu, core settings, HLE emulatated BIOS off. B returns and Quit exits.

[Tutorial] xmame change rendering mode

Select any game A to enter the menu, select Video rendering software: No scaling, press a to enter the game, and then press the left and right keys to enter the game.
 For arcade games, it is recommended to use xmame as much as possible, and use fba for those that cannot be used.
[Tutorial] Some operations of xmame make it easy for you to find out where the original game is.
So explain.
The r key switches 3 folder games, 52, 69, 84 (84 has 156 games, 52 has 2 games, and 69 has 9 games) so you press r again to switch back to the 84 folder.

The l key is to switch the folder, such as other categories under 84 files, such as all games 5014, of course, those games are not installed in 350h, most of which are displayed in red, (available-clones, available, all game) these items Switch.
So it is easy to confuse, switch to another type or other folder, and can not find the game that should be in the list.
So you press r to switch back to available156 in the 84 folder category.

[Tutorial] About 350h, only the screen is off and not standby
This architecture does not support standby, so shut down without playing. Anyway, the boot is only 3 seconds. The power button can shut down, and there are also related machine options in the system

[Tutorial] Armed Asuka 2 black screen in xmame
It is machine reading and decryption. The undecrypted rom takes a long time to read, about 1 minute. Please be patient.


[Tutorial] Game Kiddy 350H emulator brief instructions
Program installation
1. The external TF card supports EXT2, EXT3, EXT4 FAT32 exFAT format, NTFS does not support the measured maximum support 128G
256G
First get an external TF card, use the left side of dinguxcmdr to select the memory card (the location is /MEDIA/SDCARD) to save the opk file
Files are transferred to the built-in memory/MEDIA/DATA/APPS of the right machine
dinguxcmdr operating instructions A forward one level, B backward one level, Y menu (copy, cut, delete, etc.), X (select all,
New file, exit, etc.)
2.Using the USB transfer mode, the default format of the U disk is FAT32
Plug in the micro USB cable to the host, a selection box pops up, press the A key and the computer is recognized as a U disk, and the corresponding position is
/MEDIA/ROMS, just store the required files, OPK or ROM, in the U disk, pay attention to the file transfer,
Be sure to eject the USB flash drive.
OPK installation is the same as external TF card installation. Use dinguxcmdr to select the memory card on the left (location is /MEDIA/ROMS)
Transfer the opk file to the built-in memory /MEDIA/DATA/APPS of the right machine
dinguxcmdr operating instructions A forward one level, B backward one level, Y menu (copy, cut, delete, etc.), X (select all,
New file, exit, etc.)
3. File location
All opk programs are placed in /meida/data/apps
Generally, after running it once, the configuration file of the program will be generated in /media/data/local/home, and the bios file of some game consoles
Need to manually copy to the corresponding simulator bios folder
4. Other attention
The compatibility of PS emulator using non-hle mode will be greatly improved (use scph1001.bin as the configuration file bios folder,
And select the bios in the settings)
Please replace the BIOS file if some emulators crash
Instructions for using special buttons
Short press the power button once ‐‐‐‐‐‐‐‐ Forcibly exit the current running program to the main menu (utility function), which is equivalent to the home button
Press and hold the power button for 3 seconds to shut down, you can shut down in the game state
Press and hold the power button for 10 seconds ‐‐‐‐‐‐‐‐ Use when the system crashes, equivalent to the reset button
START+arrow key up-----brightness increase
START+arrow keys down-----brightness reduction
START+arrow key left‐‐‐‐‐‐Volume reduction
START+arrow key right-----volume increase simulator Instructions for use
To

[Tutorial] XMAME
The ROM list is in /media/roms/apps/xmame/xmame52/roms xmame69/roms xmame84/roms
If the game is not recognized, please press the start button, the recognized game will be refreshed
Insert coin L+SELECT, start R+select, L+R+START in-game menu, L+R+SECECT to return to the game selection screen;
Press select once to exit the simulator
Button SELECT + R: Insert coin
Button SELECT + L: start
Button SELECT + L + R: Return to the game selection screen.
Extended controls in the game (access to menus and options)
Button L + R: pause.
Button START + R: View FPS.
Button START + L: XMAME menu. which is. Redefine keys, auto ignition and more!
↑＋select: Archive
↓＋select: read file
In the game list, x is selected and turns yellow and L is added to the favorites. You can use the L key to find the game in the collection later.

[Tutorial] DOSbox
D-PAD arrow keys, in mouse mode, you can move the mouse
A Ctrl
B Alt
Y Spacebar
X Shift
L keyboard display
R Mouse mode
Start Enter
Select Escape
Keyboard mode control:
A Normal button
B-"Sticky" button (combination key use)
Y-Switch keyboard opaque/transparent
X + D‐PAD Move the keyboard on the screen
Select + Start pop-up menu
To

[Tutorial] FBA
D-PAD Move (its logic changes automatically in the spinning game)
SELECT coin
START Player starts 1
SELECT+START-Player start 2
A fire 1
B fire 2
X fire 3
Y fire 4L fire 5
R fire 6
L+R+Y-Show/hide FPS
L+R+A Fast status loading
L+R+B Fast state storage
L+R+SELECT menu
L+R+START-FBA SDL menu (you can only exit FBA from the menu)

【Tutorial】NGPCemu
SELECT menu
No key combination
[Tutorial] ohboy
L+R menu
[Tutorial] Oswan
SELECT menu
No key combination

[Tutorial] PCSX4ALL
Select + Start pop-up menu
core settings analog arrow keys are joystick functions,
When OFF, there is no joystick function, the left of the joystick is the L2 button, and the right of the joystick is the R2 button. Call down the menu and move up L2+R2
When ON, there is a joystick function SELECT+L is the L2 button SELECT+R is the R2 button
[Tutorial] PocketSNES
Select + Start pop-up menu
[Tutorial] SMS
SELECT menu
No key combination
[Tutorial] handy
SELECT menu
No key combination

[Tutorial] mame4all
After mame4all runs for the first time and selects the ROM directory, this directory will be used by default in the future and cannot be changed.
Select the ROM path, delete the /media/data/local/home/.mame4all configuration, and then run mame4all to reset
Set the ROM path.
SELECT: coins
START: start the game
START+SELECT: Main menu. Can be used to redefine the default keys for all games (use the b button) START+L+R: Esc (exit to the MAME front end)
L+R: Pause
SELECT+R: Display FPS
START+L: Display configuration file
L+B: Snapshot

[Tutorial] Regba
Select + Start pop-up menu

[Tutorial] FCEUX
Select + Start pop-up menu

[Tutorial] GameBatte
L+R menu

[Tutorial] PicoDrive
SELECT Menu

[Tutorial] Temper
SELECT menu
No key combination

[Tutorial] GnGeo
Select + Start pop-up menu

[Tutorial] Homemade Game
SORR
There is a crash phenomenon Delete the /media/data/local/home/.sorr5 configuration
note
Please do not remove the battery at any time. Removing the battery will cause the system battery gauge to restore the factory value. This will lead to
The battery power value (percent display) displayed by the system is not accurate. After removing the battery, please calibrate it as follows
Battery charge gauge.
1. Insert the battery plug into the device, turn it on until the battery is discharged below 5%, and then connect to charge
The battery is fully charged (the red charging light is off). At this time, the power may not show 100% power.
Worried about continuing to the next step
2, Continue to the previous step, continue to use the battery to below 5% of the power value, and then connect the charger until fully charged
Battery (the red charging indicator goes out), the battery power value (battery capacity) has been calibrated to the actual
capacity.
Simply put, just get the game console and play it until the red light flashes and then refill it.


[Tutorial] Other tutorials:

350H replace wallpaper and delete built-in wallpaper tutorial
1. First of all thank you mib boss for your guidance.
2. Prepare the picture, connect to the computer with the data cable, and press the a key to enter the U disk mode
3. Throw in the prepared pictures, I created a new English folder photo to make it easier to find
4. After copying, check in DinguxCmdr (double column file manager) in applications and find your own picture on the left. The directory is /meadia/roms/photo
5. Then find the system wallpaper directory /usr/share/gmen2x/skins/default/wallpapers on the right, press x to select the wallpaper to be copied on the left, and select copy from the pop-up menu, and then copy to the right directory (if you want to delete the same menu, select Just delete, I tried the default wallpapers that can be deleted)
6. The power button returns to the main menu, settings-wallpaper, and the wallpaper is selected successfully.
7. Explain the skin. There are two skins, one is GKD350 and the other is Default. The difference seems to be the number of icons arranged. The default is 3 in a row, and GKd350 is 4.
8. Other precautions The black background will not interfere with the display effect of the simulator preview image, and other images have some influence.
And the wallpaper is best left in the default/wallpapers default theme folder. If you lose other themes, it can only appear in that theme, but you can’t see the setting in other themes.

[Tutorial] Built-in text replacement tutorial
Copy about.txt to the body, open the double-column folder, select about.txt and press x, copy to /usr/share/gmenu2x, overwrite the original about.txt file

[Tutorial] Gkd350h uses otg Android U disk to transfer data to and from computer U disk and reverse charging, 2P connect to wireless controller

1. The machine revealed that it comes with OTG, and the feature of OTG is to supply power to the external device in reverse, so it can be used as a power bank. As for the 2300mah battery conversion rate, I don't know if it is good. This machine has room to change the 3900-5000mah large battery, maybe it can really be a power bank.
 
2. External USB flash drive, so you can use otg cable to directly connect external USB flash drive to transfer data. In theory, the storage mode of the mobile phone can also be set.
3. External wireless handle, the kind with receiver. Because the drivers written by Thomas may not be all compatible, and Thomas tested the handle of Baweitang, so Baweitang should be no problem. Can identify. Others require user verification. In theory, the mouse and keyboard can also be used, but it is estimated that only the dos simulator will use it. No one has tested and verified for the time being. The features of otg are actually quite big, waiting for someone to develop a new gameplay.
Support some ps4 controllers, general xbox controllers and Nintendo controllers, can the device manager vid pid code support on the computer; the supported list is:
vid_045e pid_028e
vid_0810 pid_e501
vid_2563 pid_0526

The simulator supported by the handle only supports the 2p of the fba simulator, others do not support
 
[Tutorial] GnGeo emulator is too fast, it can be solved by turning on automatic frame skipping. option-auto frame skip true

[Tutorial] Dream simulation battle 1+2 value-added version will not respond to buttons
Enter the settings menu, select the core settings, and then switch the settings of RCntFIX and VSyncWA, so that you can solve the problem of unresponsive buttons.
But I haven't played for too long, and I'm not sure it will always work.

[Tutorial] How to deal with stray stuck
1. Archive immediately
2. Exit and enter the pcsx that directly enters the simulator
3. Change the core setting, from rec to int
4. Use the simulator menu to exit, do not use the power to exit, and then go to the simulator with the directory to play the game
5. Read the real-time archive, after the crashed part, and then archive again
6. Repeat 3, 4, 5 to change int back to rec, continue playing
In a word, change to int, after crash, change back to rec to continue playing
But it must be changed by the independent simulator, otherwise it will not take effect.

[Tutorial] The fc simulator uses the bug of adjusting the audio sampling rate to 8000 to achieve acceleration

After the increase of 8000, the number of frames reaches more than 130 frames and the bug is accelerated.

[Tutorial] As for the performance mode, some difficult games are recommended to open, the best 5 is the best. Of course, the 7th gear is no problem, such as the baseball kid and the animal fighting 2 in xmame. Performance mode will increase power consumption.

【on】
GMENU2X has been created by MasimiLaNo "Ryo" TrROMeo and released under the GPL-V2 license.

This version is maintained by the Qi-hardware and opendingux teams. The latest source code can be found here:
http://projects.qi-hardware.com/index.php/p/gmenu2x

translation:
---
----
English & Italian by Massimiliano Torromeo
French by Paul Cercueil
Danish by claus
Dutch by superfly
Spanish by pedator
Portuguese (Portugal) by NightShadow
Slovak by Jozef
Swedish by Esslan and Micket
German by fusion_power, johnnysnet and Waldteufel
Finnish by Jontte and Atte
Norwegian by Lithium Flower
Russian by XaMMaX90
Polish by Artur Rojek

【other】
thank! Overlord Xiaomeng new finished all simulators and menus!
thank! Some sort of rom with mib!
thank! mib and hano1 test and feedback software bugs!
thank! The God of Light and Darkness (Lao Zhang) promotes and evaluates gkd350h, and provides an after-sales communication platform for gamers! QQ group: 588914844 
More about this source textSource text required for additional translation information
Send feedback
Side panels
History
Saved
Contribute